sht30的基于c51單片機驅動程序：#include #include #include "I2C.h" #include "SHT30.h" #define uint unsigned int #define uchar unsigned char void display(); unsigned char code tableduan[]= { 0x3f,0x06,0x5b,0x4f, 0x66,0x6d,0x7d,0x07, 0x7f,0x6f,0x77,0x7c, 0x39,0x5e,0x79,0x71 }; uchar data DIS_ROME[6]= {0,0,0,0,0,0}; //顯示緩存區（4） uchar DISP=0;//緩存區指針 uchar SCANF=0xDF;//掃描指針 sbit LED1=P1^0; sbit LED2=P1^1; sbit LED3=P1^2; sbit LED4=P1^3; sbit VOC_A=P3^5; sbit VOC_B=P3^6; sbit dula=P2^6; //IO口定義 sbit wela=P2^7; sbit key=P3^4; sbit beep_dr=P2^3; uint pm1 = 0; uint pm2 = 0; uint pm10 = 0; uchar vr=0; uint intrcnt=0; bit F_1HZ; uint voice_time_cnt; uchar Uart_Buf; uchar Rec_Addr=0; uchar mode=0; uchar Rec_Uart=0; uchar Recive_Buf[30]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}; #define key P34 #define const_key_time1 50 unsigned char ucKeySec=0; //被觸發的按鍵編號 unsigned int uiKeyTimeCnt1=0; //按鍵去抖動延時計數器 unsigned char ucKeyLock1=0; //按鍵觸發后自鎖的變量標志 unsigned char displaycnt=0; void keyscan() { if(key==1)//IO是高電平，說明按鍵沒有被按下，這時要及時清零一些標志位 { ucKeyLock1=0; //按鍵自鎖標志清零 uiKeyTimeCnt1=0;//按鍵去抖動延時計數器清零，此行非常巧妙，是我實戰中摸索出來的。 } else if(ucKeyLock1==0)//有按鍵按下，且是第一次被按下 { uiKeyTimeCnt1++; //累加定時中斷次數 if(uiKeyTimeCnt1>const_key_time1) { uiKeyTimeCnt1=0; ucKeyLock1=1; //自鎖按鍵置位,避免一直觸發 ucKeySec=1; //觸發1號鍵 } } } void keyservice() { if(ucKeySec) { displaycnt=!displaycnt; } ucKeySec=0; } void UartInit(void) //9600bps@12.000MHz { TMOD=0x01; //設置定時器0為工作方式1 TH0=0xf8; //重裝初始值(65535-500)=65035=0xfe0b TL0=0x2f; SCON=0x50; TMOD=0X21; IP =0x10; //把串口中斷設置為最高優先級， EA=1; ES=1; ET0=1; TR0=1; } void T0_time(void) interrupt 1 //定時中斷 { TF0=0; //清除中斷標志 TR0=0; //關中斷 keyscan(); keyservice(); display();