#include?“Control.h“
#include?“headfile.h“
uint8?Run_Flag?=?0;


int32?MOTOR_Duty_Left??=?0;
int32?MOTOR_Duty_Right?=0;
int32?MOTOR_Speed_Left?=?0;
int32?MOTOR_Speed_Right?=?0;?
int32?MOTOR_Speed_Left_Last?=?0;
int32?MOTOR_Speed_Right_Last?=?0;
int32?MOTOR_Left_Acc?=?0;
int32?MOTOR_Right_Acc?=?0;

float?SpeedRw?SpeedLw;
float?Speed_devSpeed_sumSteer_Radius;
int?Fres?=?0;	//?動態參數變量
/*******?電機速度測量?********/


/*************************???其他控制變量????******************************************/
uint8??Set?=?0;
float???Set_Speed;
int8?????CS_Point_Num=0;
float???CS_P_Right?=?0.50CS_P_Left?=?0.50;//差速系數
/*******************掛擋變量聲明**************/
float?Set_CS_P_Right[2]?=?{0.500.7};
float?Set_CS_P_Left[2]?=?{0.500.7};
uint8?Set_Set[2]?=?{04};
int8??Last_Error[5]Point_Error;
uint8????Point;	//目標點橫坐標
int8?????Point_Num=0;??//提前系數
uint8????Point_Mid?=?MIDVALUE;


void?Speed_Measure（void）
{??????
??????????????static?int32?ptA0_dataptH2_data;
??
????????/*******?右電機速度相關控制?********/
??????????????MOTOR_Speed_Right?=ctimer_count_read（SPEEDR_PIN）*100*Pulse_CM_coe;//右輪???
??????????????ctimer_count_clean（SPEEDR_PIN）;?
??????????????
??????????????if（gpio_get（SPEEDR_DIR））?MOTOR_Speed_Right=-MOTOR_Speed_Right;????
???????????????else?MOTOR_Speed_Right=?MOTOR_Speed_Right;??
??????????????
??????????????MOTOR_Right_Acc?=?MOTOR_Speed_Right?-?MOTOR_Speed_Right_Last;	//?計算加速度
??????????????
??????????????if（MOTOR_Right_Acc?>100）
??????????????MOTOR_Speed_Right?+=?100;
??????????????
??????????????else?if（MOTOR_Right_Acc???????????????MOTOR_Speed_Right?-=?100;
??????????????
??????????????else?
??????????????MOTOR_Speed_Right?=?MOTOR_Speed_Right;
???????????????
??????????????MOTOR_Speed_Right?=?range_protect（MOTOR_Speed_Right-500?500）;?//限幅保護
??????????????MOTOR_Speed_Right_Last=MOTOR_Speed_Right;
????????/*******?右電機速度相關控制結束?********/
???????????????
???????????????
????????????/*******?左電機速度相關控制?********/
??????????????MOTOR_Speed_Left?=ctimer_count_read（SPEEDL_PIN）*100*Pulse_CM_coe;//右輪???
??????????????ctimer_count_clean（SPEEDL_PIN）;?
??????????????if（gpio_get（SPEEDL_DIR））MOTOR_Speed_Left=MOTOR_Speed_Left;????
??????????????else?MOTOR_Speed_Left=?-MOTOR_Speed_Left;??

??????????????
??????????????
??????????????
??????????????MOTOR_Left_Acc?=?MOTOR_Speed_Left?-?MOTOR_Speed_Left_Last;	//?計算加速度
??????????????if（MOTOR_Left_Acc?>100）
??????????????MOTOR_Speed_Left?+=?100;
?????????????
??????????????else?if（MOTOR_Left_Acc???????????????MOTOR_Speed_Left?-=?100;
??????????????
??????????????else?
??????????????MOTOR_Speed_Left?=?MOTOR_Speed_Left;
??????????????
??????????????MOTOR_Speed_Left?=?range_protect（MOTOR_Speed_Left-500?500）;?//限幅保護
??????????????MOTOR_Speed_Left_Last=MOTOR_Speed_Left;
???
???????????????
???????????????
???????????????
????????????/*****************轉向和直道真實速度計算*****************/
?????????????
?????????????SpeedLw?=?MOTOR_Speed_Left

?屬性????????????大小?????日期????時間???名稱
-----------?---------??----------?-----??----
?????文件????????9805??2019-05-26?17:28??Control.c
?????文件????????1962??2019-05-14?20:34??Control.h
?????文件????????4022??2019-05-27?17:30??環島處理方法及對應代碼?（1）.txt